This pool gallon calculator tells you how many gallons your pool holds, so you can dose the right amount of chemicals. Measure at the waterline, average the shallow and deep water depths, and enter the numbers. Then take the result into the Pool Chemical Calculator.
What you need
- A tape measure marked in feet and inches
- Someone to hold the other end
That's it. You don't need the original plans.
Enter every measurement in feet. If you have inches left over, divide the inches by 12 and add that to the feet. For example, 16 feet 6 inches is 16.5 feet, because 6 ÷ 12 = 0.5.
How to measure your pool
Measure length and width at the waterline, not at the coping or the deck. Measure depth from the waterline down to the floor, not from the top of the wall. The formulas below are the ones this calculator uses. They come from the EPA pool chemical label (Reg. No. 45458-18), "Determine pool capacity," and they are the same formulas as the gallon helper inside the Pool Chemical Calculator.
Rectangular pools
- At the waterline, measure the length in feet, end to end.
- At the waterline, measure the width in feet, side to side.
- At the shallow end, measure the depth from the waterline down to the floor.
- At the deepest point, measure the depth from the waterline down the same way.
- Average the two depths: add them and divide by 2. Example: 3 feet and 8 feet is (3 + 8) ÷ 2 = 5.5 feet.
- The calculator uses this formula: length × width × average depth × 7.5.
Example (not your pool): a rectangular pool that is 32 feet long and 16 feet wide, 3 feet at the shallow end and 8 feet at the deep end.
- Average depth = (3 + 8) ÷ 2 = 5.5 feet
- 32 × 16 × 5.5 × 7.5 = 21,120 gallons
Round pools
- At the waterline, measure the diameter across the widest point, in feet.
- Measure the shallow-end and deep-end depth from the waterline down, then average them. If the floor is flat, use that one depth.
- The calculator uses this formula: diameter × diameter × average depth × 5.9.
Example (not your pool): a round pool with a 20-foot diameter and a flat 4-foot depth.
- 20 × 20 × 4 × 5.9 = 9,440 gallons
Oval pools
- At the waterline, measure the long side in feet (the longest distance across).
- At the waterline, measure the short side in feet (the widest distance the other way).
- Measure the shallow-end and deep-end depth from the waterline down, then average them.
- The calculator uses this formula: long side × short side × average depth × 5.9.
Example (not your pool): a 30-foot by 15-foot oval pool that is 3 feet at the shallow end and 7 feet at the deep end.
- Average depth = (3 + 7) ÷ 2 = 5 feet
- 30 × 15 × 5 × 5.9 = 13,275 gallons
Freeform pools
- At the waterline, measure the longest length in feet.
- At the waterline, measure the widest width in feet. For a closer estimate, measure the width in 3 to 5 spots evenly along the length, add those widths, and divide by the number of measurements. Enter that average as the approximate width.
- Measure the shallow-end and deep-end depth from the waterline down, then average them.
- The calculator uses rectangular math on those numbers: approximate length × approximate width × average depth × 7.5. It labels the result as an estimate.
Example (not your pool, and labeled an estimate): a freeform pool about 30 feet long and 18 feet wide, with a 5-foot average depth.
- 30 × 18 × 5 × 7.5 = 20,250 gallons (estimate)
If the depth slopes, or you have a spa or a tanning ledge: a sloping floor is already covered by averaging the shallow-end and deep-end water depths. Count a spa only if its water mixes with the pool, such as a spillover or a shared system: work out the spa's gallons with the same shape formulas and add them to the pool total. If the spa is separate, leave it out and treat it on its own. A tanning ledge is part of the pool. If the ledge is large and much shallower than the main pool, measure the ledge and the main pool as two separate areas, run the formula on each, and add the two results, so the shallow ledge doesn't inflate the average depth.
Why gallons matter
Chemical doses are calculated per gallon. If your gallon number is wrong, the dose is wrong: too little may not do the job, and too much can throw the water out of range. Once you have your gallons, use the Pool Chemical Calculator to see what to add, and in what order, for your pool.
Frequently asked questions
How many gallons is my pool?
Use the pool gallon calculator on this page. Pick your shape, measure length and width at the waterline in feet, then measure the shallow-end and deep-end depth from the waterline down and average those two depths. The calculator applies the formula for your shape and gives you the gallons. Take that number into the Pool Chemical Calculator so every chemical dose is sized to your pool.
How do I find my pool's average depth?
Measure from the waterline down to the floor, not from the top of the wall. Take one measurement at the shallow end and one at the deepest point, add them, and divide by 2. For example, 3 feet shallow and 8 feet deep is (3 + 8) ÷ 2 = 5.5 feet. That's the average depth the calculator uses. If a measurement is in inches, divide the inches by 12 to convert to feet (6 inches is 0.5 feet, so 3 feet 6 inches is 3.5 feet). If you can't measure the depth yourself, call (702) 626-4970 and we can measure it on a visit.
How do I measure a freeform or kidney pool?
Measure the longest length at the waterline, then the widest width. For a closer estimate, measure the width in 3 to 5 spots evenly along the length and average those widths. Average the shallow and deep water depths the same way as any other pool. The calculator uses rectangular math on those numbers: approximate length × approximate width × average depth × 7.5, and it labels the result as an estimate.
How many gallons is a 16 x 32 pool?
It depends on the depth. Use length × width × average depth × 7.5, the same formula the calculator uses for a rectangle. Example: a 16-by-32-foot rectangular pool that is 3 feet at the shallow end and 8 feet at the deep end has an average depth of 5.5 feet. 16 × 32 × 5.5 × 7.5 = 21,120 gallons. If your depths are different, enter your own measurements in the calculator instead of using this example.
Does the spa count? What about a tanning ledge?
Count the spa only if its water mixes with the pool, such as a spillover or a shared system. Work out the spa's gallons with the same shape formulas and add them to the pool total. If the spa is separate, leave it out and treat it on its own. A tanning ledge is part of the pool. If the ledge is large and much shallower than the main pool, measure the ledge and the main pool separately, run the formula on each, and add the two results, so the shallow ledge doesn't inflate the average depth.
Why does pool volume matter for chemicals?
Chemical doses are calculated per gallon. If your gallon number is off, the dose is off: too little may not do the job, and too much can throw the water out of range. The Pool Chemical Calculator sizes every dose to the gallons you enter. A measurement that's a few hundred gallons off is close enough, because the Pool Chemical Calculator works in 500-gallon steps. Guessing half the real size, though, will cut the dose in half. Once you have your gallons, use the Pool Chemical Calculator to see what to add.
Questions? Call (702) 626-4970.