Questions or ready to book?

(702) 626-4970

Mon–Fri 8am–5pm · Sat 8am–3pm

Free tool

Pool Salt Calculator: How Much Salt to Add to Your Pool

Test your salt, enter your gallons, and see how many 40-lb bags to pour.

Pick Pentair, Hayward or Jandy to set the target, or enter your own. The pounds and bags update as you type.

Built by All Pools Pro. Licensed Las Vegas pool pros.

Salt system

IntelliChlor · Target 3,600 ppm · Range: 3,000–4,500 ppm

Not sure which you have? The brand name is printed on the cell and the control box at your equipment pad.

Not sure? Find my gallons →

From a salt test strip, a pool store test or your cell's display.

—

Enter your gallons and current salt to see how much to add.

Salt Cell Cleaning

$120 one-time visit, due every 3 months

Weekly service customers get salt cell cleaning included.

We clear the calcium scale Las Vegas hard water leaves on your cell plates so your salt system can keep making chlorine.

Once your salt is set, balance chlorine, pH, alkalinity, calcium and stabilizer.

This pool salt calculator tells you how much salt to add to your saltwater pool, in pounds and in 40-lb bags. Enter your gallons and your current salt level in ppm, then pick your salt system or type your own target. It uses the same math as the salt charts in the Pentair and Hayward manuals: gallons × ppm to raise × 8.34 ÷ 1,000,000.

What you need

That's it. Measure salt before you buy any, because most pools already hold some.

How to add salt to your pool

  1. Test first. Read your salt with a salt test strip or a pool store test. Write down what your cell's control panel shows, too. If they disagree, go with the strip.
  2. Get your gallons. Use the Pool Gallon Calculator if you don't know them.
  3. Run the calculator above. Pick your salt system, or choose Custom and enter the target from your manual. Note the pounds and bags.
  4. Buy the right salt. Bags labeled pool salt, at least 99.8% pure sodium chloride, not iodized, with no anti-caking agents (often listed as YPS or yellow prussiate of soda). No rock salt and no calcium chloride.
  5. Turn the pump on and the cell off. Keep the pump running. Turn the salt cell off or set its chlorine output to 0% until the salt has dissolved. See the brand notes below for your system.
  6. Pour slowly around the edge or into the shallow end. Never pour salt into the skimmer, the main drain or a surge tank. It can clog the filter and damage equipment.
  7. Brush the floor until the salt is gone. Don't let it sit in piles on the bottom.
  8. Run the pump for 24 hours. Jandy TruClear owners: wait 48 to 72 hours before you verify the reading.
  9. Retest. Check a strip against your cell's display. If you're still low, run the calculator again with the new reading and add the difference.
  10. Turn the cell back on and set the output for your normal chlorine. Then use the Pool Chemical Calculator to dial in chlorine, pH and the rest.

Just replastered or resurfaced? Pentair and Jandy say to wait at least 30 days before adding salt, and Hayward says 10 to 14 days. Follow your pool surface maker's guidelines, and call us if you're not sure.

Brand notes

Pentair IntelliChlor — target 3,600 ppm

  • Pentair lists 3,600 ppm as the ideal salt level on the IntelliChlor Plus and LT screen. The range is 3,000–4,500 ppm.
  • Display check: the screen shows "ADD SALT" below 3,000 ppm and turns the cell off below 2,600 ppm ("SYS OFF LOW SALT").
  • Power the IntelliChlor back on and set the output only after the 24-hour retest.
  • Older IntelliChlor with LED salt lights instead of a ppm screen? Check the target in its manual.

Hayward AquaRite / TurboCell — target 3,200 ppm

  • Hayward calls 3,200 ppm optimal, with an ideal range of 2,700–3,400 ppm.
  • Display check: the salt reading can take 24 hours to respond after you add salt. A "Check Salt" light means test the salt, and a "High Salt" light means it's too high.
  • Hayward suggests a professional salt test before you add a large amount.

Jandy AquaPure / TruClear — target 3,250 ppm

  • AquaPure: Jandy recommends 3,000–3,500 ppm. The panel shows salt in gpl, so 3.0 gpl = 3,000 ppm. Set chlorine production to 00% before you add salt, then set it back after the 24-hour retest.
  • TruClear: Jandy's manual sets 3,000 ppm, so choose Custom and enter 3,000. Turn the power pack off by holding the On/Off button for 6 seconds before adding salt. TruClear doesn't measure salt, so always use a test strip, and verify 48 to 72 hours after adding.

Quick salt chart (same formula as the calculator)

Pool sizeSalt to raise 100 ppmSalt to raise 500 ppm
5,000 galabout 4.2 lbabout 21 lb (0.5 bag)
10,000 galabout 8.3 lbabout 42 lb (1 bag)
15,000 galabout 12.5 lbabout 63 lb (1.6 bags)
20,000 galabout 16.7 lbabout 83 lb (2.1 bags)
25,000 galabout 20.9 lbabout 104 lb (2.6 bags)
30,000 galabout 25 lbabout 125 lb (3.1 bags)

Bags are 40 lb.

Salt too low vs. too high

Too low (below your target)

What happens: the cell makes less chlorine. Pentair turns the cell off below 2,600 ppm. Jandy warns that running AquaPure below 2,000 ppm, or TruClear below 2,500 ppm, causes early cell failure.

What to do:

  1. Confirm with a test strip. A scaled cell can throw a "check salt" light even when the salt is fine.
  2. Run the calculator, add the salt with the steps above, and retest after 24 hours.
  3. If the strip says you're in range but the cell keeps saying low, the cell likely needs cleaning. Book Salt Cell Cleaning →

Too high (above your system's range)

What happens: Pentair warns that salt above 4,500 ppm can corrode equipment and surfaces around the pool, and Hayward says high salt can shut the AquaRite down and start to taste salty.

What to do: salt doesn't evaporate and no chemical removes it. The only fix is a partial drain and refill with fresh water to dilute it.

  1. Work out how much water to replace: (current ppm − target ppm) ÷ current ppm.
  2. Multiply by your gallons.
    Example (not your pool): 15,000 gallons at 4,500 ppm, target 3,600 ppm. (4,500 − 3,600) ÷ 4,500 = 0.20. 0.20 × 15,000 = about 3,000 gallons to replace.
  3. Refill with fresh water, run the pump, and retest. Las Vegas tap water carries minerals of its own, so you may need a little more.
  4. Never drain the pool all the way. Call (702) 626-4970 and we can do the partial drain and refill for you.

Don't add more salt until you're back in range.

Weekly service note: weekly customers get salt cell monitoring on every weekly visit, all year, with chemicals included.

Frequently asked questions

How much salt do I add per 10,000 gallons?

About 8.3 pounds for every 100 ppm you need to raise it (10,000 × 100 × 8.34 ÷ 1,000,000 = 8.34 lb). So a 10,000-gallon pool at 2,800 ppm needs about 33 lb to reach Hayward's 3,200 ppm, or about 67 lb to reach Pentair's 3,600 ppm. A freshly filled 10,000-gallon pool with no salt needs about 267 lb, or about 6.7 bags of 40 lb, to reach 3,200 ppm. Test first, because most pools already hold some salt.

How long should I wait before I retest the salt or swim?

Brush the salt in and run the pump for 24 hours, then retest. Pentair, Hayward and Jandy AquaPure all call for 24 hours of circulation before you trust a new reading, and Hayward notes its salt display can take 24 hours to catch up. Jandy's TruClear manual says to verify the salt after 48 to 72 hours. Turn your cell back on only after that retest. None of these manuals sets a separate swim wait for salt. If you added other chemicals at the same time, follow the wait on those labels.

Can my salt cell's reading be wrong?

Yes, so check it against a salt test strip or a pool store test before you add salt. Pentair's IntelliChlor manual says its salt sensor reads within plus or minus 500 ppm, and Jandy says water temperature can affect the salinity readout. Jandy's TruClear doesn't measure salt at all: on an automation screen it shows its 3,000 ppm target, not a reading. In Las Vegas hard water, calcium scale on the cell plates is a common cause of "check salt" and "inspect cell" lights. If a strip reads in range but your cell says low, book a Salt Cell Cleaning before you add more salt.

Do rain and splash-out lower the salt level?

Yes. Hayward's manual says salt is lost when water leaves the pool through splashing, backwashing or draining because of rain, and that salt is not lost to evaporation. Topping off water that evaporated doesn't lower your salt. Replacing water that splashed out, overflowed or was backwashed does. Test the salt after heavy rain or a big backwash, and always before you add any.

What kind of salt should I buy?

Buy bags labeled pool salt that are at least 99.8% pure sodium chloride, which is what Pentair and Jandy call for (Hayward says greater than 99% pure). Pick evaporated, granulated, food-quality salt that is not iodized and has no anti-caking agents, which are often listed as YPS or yellow prussiate of soda. Don't use rock salt or calcium chloride. Water-softener pellets dissolve slowly, and Pentair warns they can damage plaster, so plain pool salt is the safer pick.

How do I lower my salt if it's too high?

Salt doesn't evaporate, and Hayward's manual says the only way to lower it is to partially drain the pool and refill with fresh water. To find how much water to replace, use (current ppm − target ppm) ÷ current ppm. Example: a 15,000-gallon pool at 4,500 ppm with a 3,600 ppm target is (4,500 − 3,600) ÷ 4,500 = 0.20, so replace about 20%, or about 3,000 gallons. Las Vegas tap water carries minerals of its own, so retest after the refill. Never drain the pool all the way. Call (702) 626-4970 and we can do the partial drain and refill for you.

Once your salt is set, balance chlorine, pH, alkalinity, calcium and stabilizer.

Now test your water

Every salt dose starts with your gallons.

Find my gallons →

Want us to keep your salt, chlorine and cell in check every week?

Free Quote →

Questions about your salt system? Call (702) 626-4970. Licensed Las Vegas pool pros.

📞 Call Now Free Quote